RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0105629 REAR VIEW MONITOR SYSTEM(for Radio and Display Type) Y

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM(for Radio and Display Type)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use these procedures to troubleshoot the rear view monitor system.

·

*: Use the GTS



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CHECK AUDIO AND VISUAL SYSTEM*
4.CHECK AUDIO AND VISUAL SYSTEM*
a.

Refer to DTC Check/Clear procedures of the audio and visual system.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

5.CHECK FOR DTC*

DTC is output

GO TO AUDIO AND VISUAL SYSTEM

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR


5.CHECK FOR DTC*
a.

Check for DTCs and note any codes that are output.


b.

Clear the DTC

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Proceed to
DTCs are not output.
DTCs are output.


HINT:

Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.




DTCs are not output.

6.PROBLEM SYMPTOMS TABLE

DTCs are output.

GO TO DIAGNOSTIC TROUBLE CODE CHART

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM(for Radio and Display Type)>DIAGNOSTIC TROUBLE CODE CHART


6.PROBLEM SYMPTOMS TABLE
a.

Refer to the problem symptoms table.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM(for Radio and Display Type)>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
Fault is not listed in problem symptoms table
Fault is listed in problem symptoms table



Fault is not listed in problem symptoms table

7.BASED ON MALFUNCTION SYMPTOM, PERFORM TROUBLESHOOTING BELOW

Fault is listed in problem symptoms table

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

7.BASED ON MALFUNCTION SYMPTOM, PERFORM TROUBLESHOOTING BELOW
a.

Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM(for Radio and Display Type)>TERMINALS OF ECU


Result:
Proceed to
NEXT



NEXT

8.ADJUST, REPAIR OR REPLACE
8.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

9.CONFIRMATION TEST
9.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END